A Step-by-Step Overview to Setting Up a Bathtub
A Step-by-Step Overview to Setting Up a Bathtub
Blog Article
We've unearthed the article involving Installing A Bathtub directly below on the net and accepted it made perfect sense to discuss it with you over here.
Installing a bath tub isn't specifically brain surgery, yet it does need solid plumbing, carpentry, and in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately hard task. If the old tub is readily obtainable, the job can relocate quickly; if you need to open a wall surface to remove the old bathtub and place the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. Make sure you have qualified on your own for the work and also fit trying it. Rather than working with a contractor to take control of a halfway-completed project, it is better to consider using one before you begin. Chances are you might require a specialist plumber to make tube links.
This article will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently gotten a new tub and also do not need to change the setup of your previous water pipes.
Your tools and also product checklist should consist of the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your setup, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted accessibility that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet and the sink. Safeguard the faucet in place with the manufacturer given backnut. When the faucet is securely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Making use of the two wood boards under its feet, put the bathtub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as readjusting the feet on the bathtub till the level reviews level.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the very same for the other tap.
Activate the water supply as well as examine all joints and brand-new pipework for leakages and tighten them if needed. Load the bathtub and additionally check the overflow outlet and also the regular outlet for leakages.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bath tub should wait up until the bath tub has actually been used a minimum of when as this will certainly resolve it into its final setting.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a stiff seal, triggering the water to pass through the wall between the bath and also the tiling, causing issues with dampness and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack relatively early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently offered on the market. It is a good idea to fit the tiles utilizing water-resistant or water resistant glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that blog posting about A Step-by-Step Guide to Installing a Bathtub when doing research the internet. Liked our blog entry? Please share it. Help somebody else find it. Many thanks for your time. Don't hesitate to come visit our blog back soon.
Book Now
Report this page